Seneste nyt om:

Seminarer • konferencer
kurser • messer
Send til en ven   Udskriv18/6 2010 kl. 10:15
Send til en ven

Remote access software til Agilent oscilloskoper

Agilent Technologies introducerer remote access software til Infiniium 86100 serien af DCA oscilloskoper (in english).

Agilent Technologies Inc. has introduced N1010A FlexDCA remote access software and the N1010A-SIM InfiniiSim-DCA waveform transformation toolset for the Agilent 86100C/D DCA (digital communications analyser) family of wideband oscilloscopes.

In addition to providing a powerful new user interface, FlexDCA offers de-embedding, embedding and virtual probing capabilities that help engineers characterise high-speed digital designs more thoroughly and with improved margins.
 
As data rates increase, fixtures and probes tend to degrade waveform fidelity and reduce measurement margins to a greater degree. Engineers often need to remove these unwanted effects to see the true performance of their devices during verification or compliance testing.


Engineers also commonly need to measure a clean transmitter and simulate the signal at the output of a typical channel loss model. The N1010A-SIM InfiniiSim-DCA waveform transformation toolset allows engineers to perform both of these tasks quickly and accurately.
 
The PC-based N1010A FlexDCA remote access software provides:
 
-  a new customisable user interface for scope, eye and jitter measurements;
 
-  new measurements, including data-dependent pulse-width shrinkage, uncorrelated jitter and pre- and de-emphasis;
 
- improved accuracy and insight (using N1010A Option SIM);

- an advanced, graphical signal processing interface, which enables more sophisticated analysis capabilities and improved usability; and
 
- the ability to perform connected and offline measurements. 
 
N1010A Option SIM InfiniiSim-DCA provides:
- de-embedding and embedding capability;
 
- improved accuracy and measurement margins;

- simultaneous display of measured and simulated waveforms;

- and scope, eye and jitter measurements on simulated signals. 
 
To create accurate simulations, engineers need precision measurements, accurate models and robust waveform transformation algorithms. The 86100C/D DCA and N1010A FlexDCA software meets all three of these needs:

- The DCA-J combines high-bandwidth, low-noise and ultralow jitter acquisition hardware to yield extremely accurate measurements.

- N1010A Option SIM accepts a variety of models, including S-parameter files generated by the 54754A TDR/TDT module and 86100C-202 S-parameter software. S-parameter data may also be generated by VNAs or design software such as Agilent’s Advanced Design System. Models can also be defined using transmission line or RLC parameters.
 
- Waveform transformation is performed by calculating a transfer function between measured and simulated nodes. N1010A Option SIM uses proven algorithms that were leveraged from the Agilent N5465A InfiniiSim waveform transformation software designed for the 9000 Series and the 90000 Series real-time oscilloscopes.
 
- FlexDCA is another Agilent innovation that gives engineers the tools they need to tackle their tough design challenges when they are working with high-speed digital signals, says Alexander, vice president and general manager of Agilent’s oscilloscopes business. “N1010A FlexDCA and the 86100C/D provide a complete measurement and simulation solution that speeds time to market for new designs. 
  
Additional information about Agilent’s N1010A application is available at www.agilent.com/find/n1010a.

Danish distributor:
Altoo Measurement Science ApS, 
kunde.service@altoo.dk
Phone: 70 13 15 15
www.altoo.dk

Relaterede nyheder

Forrige1234567891011Næste

Elektronik & Data • Odsgard A/S • Stationsparken 25 • 2600 Glostrup • Tlf: +45 4345 1063