Nye EV-sikkerhedsstandarder bringer Kina i front
Kina's GB 38031-2025 EV-sikkerhedstandard, der træder fuldt i kraft i juli 2026, sætter helt ny målestok for den krævede sikkerhed i elektriske biler, fastslår analysefirmaet IDTechEx (in english).
Author: Dr James Edmondson, VP Research at IDTechEx
China's GB 38031-2020, implemented at the start of 2021, set the level for the global industry on EV thermal runaway safety. It was the first mandated standard with a 5-minute warning for occupants to escape the vehicle. In April 2025, it was announced that China's GB 38031-2025 would be mandated by July 2026 for new vehicles. This 2025 update goes well beyond the previous one with the requirement for no fire or explosion for 2 hours after the initial event.
Whilst China continues to outpace the world in EV sales, with EVs accounting for 49% of new car sales in 2024, according to IDTechEx research, it is also ahead of the rest of the world with safety standards.
China's new requirements
There are a few key changes for China's 2025 version of the 38031 standard. The most surprising is the requirement for no fire or explosion for 2 hours after the initiation of thermal runaway in a single cell. The warning to the vehicle occupants is still present, and no visible smoke should enter the passenger compartment within 5 minutes of the event.
The standard also adds internal heating as a testing trigger mechanism to the list, with external heating and puncturing. If thermal runaway does not occur with one of these test methods, the other methods should be tested.
China's EV market has become increasingly dominated by LFP chemistry, which makes adhering to this challenge easier than with the higher energy density NMC chemistries. But it is still not straightforward, as no energy storage system is 100% inherently safe.
What is clear is that China's standards are moving much quicker with regard to thermal runaway in EVs than other regions that are still going through drafts, revisions, and updates with no mandated standards in place.
What's happening in Europe?
Europe is looking to the UN ECE R100 standard and its changes. The R100-05 version is set for implementation for new vehicle types in September 2027 and all new vehicle types by September 2029. Significantly behind China's 2026 implementation, and has requirements that are much more similar to China's 2020 standard! A 5-minute warning to vehicle occupants after a thermal event, during which no hazardous situation can occur for the occupants (fire, smoke, or explosion).
The latest updates look to have more specificity in the testing mechanisms, rather than the final safety outcome.
Is the US even further behind?
Whilst the US also looks at the UN ECE regulations, NHTSA is the key body for mandating safety. Its latest revision of FMVSS 305a closely follows the UN ECE regulation, but has taken a less stringent standard for safety. Here, there is no need to detect single cell thermal runaway but is completely based on the temperature within the pack.
Whilst GTR20 requires a 5-minute warning between a single cell entering thermal runaway and danger to the occupants, NHTSA argues that detecting a single cell would be "unduly design restrictive" and not relevant in all conditions.
Rather than having a warning that is triggered by a single cell failure, NHTSA instead proposes a warning system that is triggered by temperatures inside the battery system significantly exceeding the maximum operating temperature. To test this system, the battery should be opened, and a heater that reaches 600°C in 30 seconds is attached to the cell/cells such that at least a single cell enters thermal runaway. The warning must occur within 3 minutes of the heater initiation.
How do automakers adapt?
When China announced the 2020 standard, automakers largely adapted existing battery platforms to meet the new standard. This time, automakers have been considering fire safety at a much earlier stage in the design process and have been trying to exceed the 5-minute warning.
However, the new 2-hour need from China is a huge curveball, preventing thermal runaway between cells is certainly possible and several material options exist, but as always, there is a trade-off in performance and price for each battery design. This all comes at a time where reducing battery costs is paramount for future EV adoption.
Having safer vehicles is certainly a good thing, but also a major challenge to automakers and battery designers. Automakers tend to want a design that can be used globally without too many alterations for a specific market.
IDTechEx's report, "Fire Protection Materials for EV Batteries 2025-2035: Markets, Trends, and Forecasts", predicts that the market for these materials will experience a 15% CAGR with the growing EV market and increased focus on fire safety. It is certain that fire protection will continue to be considered at an early stage in the design process and presents huge opportunities for materials suppliers that can help automakers meet these new requirements.
For more information on this report, including downloadable sample pages: www.IDTechEx.com/FPM.
